Pipeline inspection9 min read|Updated 20 November 2026

Injection Point Corrosion: Map UT Points and Gaps

Scope an injection-point UT survey in France. Locate valid pipe-wall readings and record hidden quill, branch and fitting surfaces.

PetroBot Technologies ·

English technical guide for asset-integrity and industrial-inspection professionals in France.

Illustration of an elevated steel injection tee and downstream elbow in a pipe rack
Injection pointsLocalized corrosionUT mappingMagRover

Consider a carbon-steel injection spool with old thickness readings only on its upper face. The line drawing shows a branch at the tee; a rack support blocks the planned route around the first downstream elbow. Keep the valid readings, then mark the lower pipe wall, blocked elbow sector and quill interior for separate follow-up. The spool is hypothetical.

At an injection point in France, the installed drawing and process history set the pipe-wall survey and its limits.

Direct answer

Start with the injection drawing and process history. Mark the tee or quill, flow direction, nearby fittings and surfaces that need examination. Confirm the external layout visually, then take UT readings on accessible parent-pipe steel under the approved procedure. Record valid thickness points, failed attempts and unexamined surfaces separately. MagRover can support the external visual and UT route if the pipe, surface and access suit the robot. The owner's piping inspector sets the survey extent, assigns a separate method for hidden injection hardware and reviews the results with the corrosion specialist.

Technical sources: HSE Humber Refinery investigation, API Inspection Summit injection-hardware abstract, API 570 and RP 574 publisher scope and additional references.

Key takeaways

  • Use the controlled drawing and injection history to set the survey extent.
  • Locate every parent-pipe UT point by datum, flow direction, distance and clock position.
  • Record valid readings, failed UT attempts and untouched surfaces in separate states.
  • Give the quill, branch interior and blocked fitting sectors a named follow-up.
  • Send the map and open decisions to the owner's piping inspector.

What changes at a chemical injection point?

An injected fluid joins the main stream through a tee, quill or another fitting. The hardware, flow and fluids shape where mixing occurs and which surfaces need inspection. The parent wall, injection hardware and first fitting may raise different damage questions. Use process records and examination results to assess corrosion, erosion, deposits or hardware damage; an external image cannot identify the internal mechanism.

The UK HSE investigated a refinery elbow that thinned downstream of a water injection point. Investigators linked the localized loss to the water flow path. The water entered through an existing vent point as a free jet; no quill was fitted. The case shows why each survey needs the installed drawing and operating history.

An API Inspection Summit abstract names tees, quills, nozzles and spargers as different injection arrangements. Identify the installed hardware before assigning an examination to each surface.

Which drawings and process records set the scope?

Get the controlled P&ID, line isometric and injection-assembly drawing. Check the line ID, revision, material, diameter, wall, coating, flow arrow, branch detail and first downstream fitting against the installed pipe. Add earlier monitoring locations, UT traces, repairs and quill examination records.

Ask operations when injection started or stopped and whether the fluid, dose or service changed. An old route may miss the present damage question. API 570 covers in-service piping inspection and RP 574 covers piping-component practices. The owner uses its adopted editions and inspection program to set this line's extent.

How do you locate the parent-pipe survey?

Choose a datum at the injection junction, confirm flow direction and mark the selected upstream and downstream points on the isometric. Record each distance and clock position using the owner's viewing convention. Include the first fitting and outline any sector the route cannot reach. The piping inspector sets the extent and grid from the suspected damage, process history and applicable program.

In the example, old upper-face readings remain useful at their recorded locations. They say nothing about the lower wall. Show planned pipe points, the quill interior and the blocked elbow sector as distinct items on the map.

Illustrative injection-point pipe routeFlow passes a vertical injection branch and selected parent-pipe clock positions before a downstream elbow. The branch interior and far elbow sector remain unexamined.FlowInjection branchSelected positionsElbow gap
Map key 1

Injection datum and flow

Use the controlled junction drawing to locate points upstream and downstream.

Map key 2

Selected clock positions

Record the viewing convention and drawing revision with each pipe point.

Map key 3

Quill interior

The external UT route does not examine the bore or tip.

Map key 4

Downstream elbow gap

Name the sector behind the support and assign its follow-up.

Use the installed drawing for the flow arrow, datum and UT locations. Assign the quill interior and blocked elbow sector separately.

Where can MagRover actually run?

MagRover adheres to ferrous surfaces and can collect external visual records and UT spots or scans. A suitable parent-pipe route may reach the junction, but the robot does not enter the branch or inspect the quill bore. Check material, pipe size, curvature, coating, surface preparation, temperature, clearance and the recovery path on the installed line.

Before deployment, the site team confirms the permit, area classification and suitability of the actual equipment configuration. Agree the operating state, power and tether path, dropped-object controls and recovery method. Trial adhesion and probe response on representative pipe under the owner's NDT procedure. Stop at an attachment, bend or surface the approved route cannot cross, and mark that boundary.

When is a UT reading usable near the junction?

Verify the instrument and probe against the material and approved procedure. At each point, check the surface, coating, coupling and UT response. Save the trace, location, surface condition and preparation record with a valid thickness. If the response fails, record the attempted point and reason without a thickness number.

ISO 16809:2025 describes time-of-flight ultrasonic thickness determination; ISO 16831:2025 addresses equipment verification. Accept readings only after the actual coating and robot setup pass the owner's procedure. HSE guidance calls for locations and a method that suit the damage sought. A valid upper-face point cannot clear an untested lower sector.

What does a localized low reading establish?

A valid low reading gives thickness at one recorded spot. Confirm its trace, equipment checks, surface and clock position, then report it under the site's escalation process. The piping inspector decides whether to extend the survey around that point. The corrosion specialist compares the pattern with process and material evidence before naming a mechanism.

A low point alone cannot establish minimum required wall, corrosion rate or remaining life. The owner makes those assessments under its piping program. Keep the same datum and location convention for later surveys so teams can compare the same positions.

Which parts of the quill and fitting remain unseen?

An external pipe route cannot examine the quill bore and tip, branch interior or internal mixing face. It may also miss an attachment weld or bend sector. Mark each gap on the assembly drawing. A valid point beside the branch says nothing about its interior.

In the example, a fixed rack support blocks the lower and far side of the downstream elbow. Record that sector as unexamined. The inspector can then choose another qualified method, different access or an outage examination if the integrity question requires one.

Illustration of a downstream steel elbow partly hidden by a fixed pipe-rack support
The support hides part of the elbow. Mark that sector as unexamined on the route map.

How do you hand off when a robot cannot reach?

Mark the last confirmed point, feature, drawing revision, flow position and clock sector. State whether adhesion, clearance, coating, probe response or access stopped the work. A failed UT attempt is a rejected point; a surface never reached is unexamined. Give neither a zero nor an estimated thickness.

Give each gap to the piping inspector for a method decision. The next step may be local access work, another NDT setup or an outage opening. Keep the boundary beside the valid results on the same map.

What should the inspection record contain?

Return the controlled drawing with the flow arrow, injection datum, selected points and actual route. Attach external images and valid UT values with traces. List failed attempts, unexamined surfaces and pending owner decisions separately. The example below shows how to log each state; use the site's own identifiers and records in the work pack.

Example injection-spool register. These entries are not field measurements.
Feature / drawingFlow location and clockSurface / method / stateEvidence and next action
Parent pipe P1 / Rev ADownstream of tee; 12 o'clockPrepared steel / UT / ACCEPTEDTrace U-01 and value in site record; inspector reviews coverage
Parent pipe P2 / Rev AAt tee; 6 o'clockCoated steel / UT / REJECTEDTrace U-02; no thickness; NDT lead reviews surface and setup
Quill bore Q1 / Rev AInside branch; clock not applicableInternal surface / no method / UNEXAMINEDPiping inspector selects a separate examination
Elbow sector E1 / Rev AFirst fitting downstream; far lower sectorSupport blocks route / UNEXAMINED; decision DEFERRED TO OWNERImage I-03; piping inspector assigns access and integrity review

Who makes the integrity decision?

Give the owner the drawing-linked map, valid values and traces, failed attempts, external observations and named unseen surfaces. Escalate a confirmed low point through the site's process. The piping inspector and corrosion specialist decide what to examine next, assess the mechanism and determine any repair or operating action under the owner's program.

Bring the injection drawing, earlier UT map and operating changes to that review. Use the elbow guide for bend measurement geometry and the dead-leg guide if stagnant service adds another damage question. Keep a gap open until the assigned examination or owner decision is on record.

Frequently asked questions

Can MagRover inspect the injection quill?

No. MagRover can inspect suitable external parent-pipe surfaces. The quill bore, tip and hidden junction need a separate examination chosen by the owner.

Where should UT readings go around an injection point?

The piping inspector sets the extent from the installed drawing, process history, suspected damage and inspection program. Locate each point by datum, flow direction, distance and clock position.

Does one low reading prove injection-point corrosion?

No. Confirm the value and location under the approved procedure. The corrosion specialist reviews the pattern and process evidence before assigning a mechanism.

Can MagRover cross a branch weld or elbow?

Test adhesion, clearance and probe response on the installed geometry. If the route stops, map the gap and ask the inspector to select another qualified method.

Can UT read through the pipe coating?

The approved procedure and a representative trial must show a valid response for that coating and setup. If they do not, log a rejected attempt without a thickness value.

What should the owner receive?

A drawing-linked map, valid UT points and traces, failed attempts, external images, unexamined surfaces and a named owner for each next action.

Technical references

Scope the injection-point survey

Send the injection drawing, service, material, earlier UT map and access plan for a pipe-route review in France.

Related guides